Leading 10 typical forklift accidents ， forklift operation should focus on these issues ！.

Leading 10 typical forklift accidents ， forklift operation should focus on these issues ！.

Blog Article

Don't undervalue the forklift at work. If the operation is bad, there will certainly be significant accidents in minutes, and there are many accidents including forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual ahead might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender throughout a turn.
Case 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation should take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is secure and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole needs to be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal needs to be released first. High-speed sharp turns are forbidden. High-speed doglegs will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with tons unless there are special conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever operate with illnesses or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with Stand-on Electric Pallet Stacker the brake. .
4. The speed of the automobile ought to be slow-moving and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm people. .
8. Straining is banned, and it is restricted to utilize forks to raise employees to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the parking Electric Forklift Truck for Warehouse brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be slow-moving and uniform, and no turning on the slope is allowed.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the lorry ought to be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not permitted under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844